HOTLINE 0086-29-88606479
  Tel: 86-29-88606479   E-mail: sales@dechuang-auto.com

NEWS

About us

Instrument knowledge| Installation and use of Insertion intelligent electromagnetic flow meter

DATE: 2021-01-14
BROWSE TIMES: 100

 

Instrument knowledge| Installation and use of Insertion intelligent electromagnetic flow meter


There are many types of electromagnetic flow meters, which can be divided into pipeline electromagnetic flow meters and plug-in electromagnetic flow meters according to different installation methods. The plug-in electromagnetic flow meter retains the advantages of the previous pipeline electromagnetic flow meter, but also overcomes the shortcomings of the pipeline electromagnetic flow meter on large-diameter pipelines, such as difficulty in installation, high cost, and difficulty in periodic calibration. It is widely used in tap water, steel and iron. , Petroleum, chemical industry, industry, water conservancy and other sectors of conductive fluids, as well as acid, alkali, salt and other corrosive conductive liquid flow measurement.

Instrument knowledge| Installation and use of Insertion intelligent electromagnetic flow meter

Let us take a look at the plug-in electromagnetic flow meter together.

The basic structure of the plug-in electromagnetic flowmeter is as follows:

 Instrument knowledge| Installation and use of Insertion intelligent electromagnetic flow meter

1. Choice of installation environment

Keep away from equipment with strong electromagnetic fields as much as possible, such as high-power motors, high-power transformers, etc.

There should be no strong vibration at the installation site, the pipes should be firmly fixed, and the ambient temperature should not change too much.

The installation environment should be easy to install and maintain.

2. Choice of installation location

The installation location must ensure that the pipe is always filled with the fluid being tested

Choose a place where the flow of fluid is small, that is, it should be far away from local resistance parts such as pumps, valves, and elbows.

The diameter or circumference of the side tube is easy to measure, and the ellipse should be small.

Avoid measuring negative pressure on site.

When measuring two-phase (solid, liquid, gas, liquid) fluid, the plug-in electromagnetic flowmeter should be selected where it is not easy to cause phase separation.

3 . Opening requirements

There are two straight pipe sections on site: the vertical straight pipe section and the horizontal straight pipe section. Measure the length of the two straight pipe sections. The larger one is preferred;

Try not to have a bypass pipe in the straight pipe section. If there is, the smaller the diameter, the better. There is no bypass pipe preferred.

The installation location is far away from solenoid valves, pumps, frequency converters, and the longest distance is preferred;

Select the straight pipe section, and open holes at the ratio of straight pipe section 3:7, the upstream ratio of the opening is 7 and the downstream ratio is 3, that is, the longer the front straight pipe section of the flowmeter, the better;

Note: The opening position is far away from the solenoid valve, pump, inverter, as the first priority.


4. Welding of the mounting base

The axis of the installation base pipe and the axis of the tested pipe are perpendicular to each other;

Conventional stainless steel flanges are flat welded with stainless steel electrodes, and PVC pipes can be welded with hot melt adhesive tape. After welding, ensure that the flange end face is parallel to the pipe axis, and the welding seam is firm, and can withstand 1.6MPa pressure without leakage;

The opening size of the pipe under test is the same as the outer diameter of the installation base.

5. Sensor installation

The sensor should be installed perpendicular to the measuring pipeline, and the angle between the sensor and the vertical diameter of the pipe section when inserted into the pipeline should be less than 5°. It is suitable for measuring clean media with small vibrations in the pipeline.

There are two ways to insert the sensor: one is to insert it on the central axis of the pipe under test (that is, 1/2 times the pipe diameter); the other is to insert it into the inner wall of the pipe at 1/4 of the pipe.

Turn off the upstream flow control valve or use low-pressure water supply, install the DN50 ball valve on the base, pay attention to the long cavity of the ball valve upwards, check whether the ball valve can be fully opened and fully closed, if there is any problem, repair it. Install the compression threaded seat, compression nut and rubber sealing ring on the ball valve, loosen the positioning screw and compression nut, and insert the sensor insertion rod into the tested pipe through the ball valve. After the insertion depth meets the requirements, tighten the nut and the positioning screw. At the same time, pay attention to the direction of the sensor direction indicator pole to be consistent with the fluid flow.

6.ground

In order to make the meter work reliably, the flow signal generated by the sensor is very weak, usually in the microvolt or millivolt level. Preventing the influence of external electrical interference is an important factor in the good use of the flow meter, and grounding is a very effective measure to solve the impact of electrical interference. Therefore, the sensor should have a good separate grounding wire with a grounding resistance of <10Ω. If the pipeline connecting the sensor is coated with an insulating layer or a non-metallic pipeline, grounding rings or built-in grounding electrodes should be installed on both sides of the sensor.

Grounding method on metal pipe: The inner wall of the metal pipe has no insulating layer, so it is grounded as show below.

Instrument knowledge| Installation and use of Insertion intelligent electromagnetic flow meter

 

Grounding method on plastic pipes or on painted pipes with insulation layer: Grounding rings or built-in grounding electrodes should be installed on both ends of the sensor, so that the measured medium flowing in the pipe is short-circuited with the earth and has zero potential. Otherwise, the electromagnetic flow meter cannot work normally. (See below)

Instrument knowledge| Installation and use of Insertion intelligent electromagnetic flow meter


Share to
RELATED NEWS / News More
  • Number of clicks: 100
    2021 - 01 - 14
    Instrument knowledge| Installation and use of Insertion intelligent electromagnetic flow meterThere are many types of electromagnetic flow meters, which can be divided into pipeline electromagnetic flow meters and plug-in electromagnetic flow meters according to different installation methods. The plug-in electromagnetic flow meter retains the advantages of the previous pipeline electromagnetic flow meter, but also overcomes the shortcomings of the pipeline electromagnetic flow meter on large-diameter pipelines, such as difficulty in installation, high cost, and difficulty in periodic calibration. It is widely used in tap water, steel and iron. , Petroleum, chemical industry, industry, water conservancy and other sectors of conductive fluids, as well as acid, alkali, salt and other corrosi...
  • Number of clicks: 160
    2021 - 01 - 12
    26GHz high frequency radar level transmitter is the mainstream product of solid level measurement.The maximum measuring distance up to 70 meters. The antenna is further optimized, and the newtype microprocessor can perform higher rate of signal analysis and processing, making the instrument available for complex measurement conditions, such as reactors, solid silos.The 26GHz high frequency radar level transmitter(DCRD1000Aseriesare researched and produced by Xi’an Dechuang El...
  • Number of clicks: 1001
    2021 - 01 - 07
    Application case|80Ghz FMCW radar level transmitter applied to the measurement of the liquid level in the refined evaporation kettleEthanol, an organic compound, molecular formula C2H6O, simple structural formula CH3CH2OH or C2H5OH, commonly known as alcohol. Ethanol can be used to make acetic acid, beverages, flavors, dyes, fuels, etc. Ethanol with a volume fraction of 70% to 75% is also commonly used in medical treatment as a disinfectant, etc. It is widely used in national defense chemical industry, medical and health, food industry, industrial and agricultural production.Our 80G frequency modulated radar level transmitter measures liquid level and material level, non-contact level measurement, strong anti-interference ability, can overcome the influence of steam, foam and sti...
  • Number of clicks: 282
    2021 - 01 - 05
    Factory produce DCRD1000A4 with air purge set for measuring the level of bulk solid heavy dust solid powder level sensorThis radar level transmitter uses a parabolic antenna with an emission angle of only 4 degrees.For a variety of complex conditions, especially the measurement of a large range of solid materials.The antenna is parabolic, so it is not easy to accumulate dust, which is very suitable for heavy dust conditions.There is a special working condition, the customer requires this section to also have a air purging device. Our technical department has researched and developed a purging device, as shown below. Since its operation, the effect are very good and has been recognized and praised by customers.
  • Number of clicks: 363
    2020 - 12 - 29
    Dechuang Radar Level Measuring InstrumentsAs a leading manufacturer of the radar level transmitter, continuous level measuring for solid and liquid medium, products as follows:1. 6.8GHz contact Guided wave radar radar level transmitter2. 26GHz non-contact pulse radar level transmitter3. 120GHz FMCW radar level  transmitter4. 80Ghz radar level sensorThere are some common application and our recommended model :1. Petrochemical: Vapors, Steam, High temperatures, Pressure, Slightly corrosive liquid.DCRD1000B 120GHz radar level transmittter; DCRD1000A2 26ghz Pulse Radar Level Transmitter.2. Cement: Long ranges, high temperatures, strong dust, crystallization?DCRD1000A3 or DCRD1000A4 26ghz pulse radar level transmitter mean zero maintenance plus efficient, reliable process control...
Email:sales@dechuang-auto.com
Adress:
Tel:86-29 88606479
Fax: 86-29 88385903
B203, Gazelle Valley, No.69 Jinye Rd, Hi-tech zone, Xi'an, Shaanxi Province, P.R.China. 710077
Copyright ©2018 - 2019 Dechuang Electrical Technology Co., Ltd SITEMAP
Rhino Cloud Provides Enterprise Cloud Services
犀牛云提供云计算服务